Image for Illustrative Purposes Only
Metcal PS-900 Production Soldering System with Tip H/Piece
SKU: METPS-900
PS-900
DESCRIPTION
Features
Shipping & Delivery
Metcal PS-900 Production Soldering System with Tip H/Piece
The PS-900 packs power and provides exceptional thermal control into a small benchtop footprint.
Discover the Metcal PS-900 Production Soldering System with Tip H/Piece at Mektronics Australia – your trusted source for quality tools and equipment!
-
SmartHeat ® temperature control
-
Ergonomic, lightweight handle
-
Rugged cast aluminum housing
-
Added plating thickness to tips
-
Low cost, quick-change heater coil
-
PS-PW900 Power Supply
-
PS-HC3 Hand-piece with long cord with Coil Assembly
-
SFV-CH15A Chisel soldering tip 1.5mm (.06")
-
WS2-NS Workstand
-
AC-CP2 Tip removal pad
Tips / Cartridges Series compatible with this system:
-
SxV Soldering Tips
-
CxV Blade Tips
| Power Supply | |
|
Output Frequency: |
450 KHz |
|
Output Power: |
60 Watts max. at 22 °C ambient temperature |
|
Power Consumption: |
90 Watts max. |
|
Input Line Frequency: |
50/60 Hz |
|
Input Line Voltage: |
100 - 240 VAC |
|
Maximum Enclosure Temperature: |
65 °C |
|
Ambient Operating Temperature: |
10 - 40 °C |
|
Power Cord (3-wire): |
274 cm 18/3 SJT |
|
Dimensions W x D x H: |
80 x 160 x 115 mm (3.1" x 6.3" x 4.5") |
|
Soldering Handle and Coil Assembly |
|
|
Tip to grip: |
58 mm (2.28") |
|
Grip diameter: |
13 mm (0.51") |
|
Overall length (with tip): |
230 mm (9.06") with standard tips Connector 3-pin power connector |
|
Handle Cord Assembly Length: |
122 cm - burn proof, ESD safe |
|
Idle Temperature Repeatability: |
± 1.1 °C in still air |
|
Tip-to-Ground Resistance: |
< 2 ohms |
|
Tip-to-Ground Potential: |
< 2 mV |
|
Tip shaft diameter: |
8.0 mm (0.31") |
|
Tip length: |
82 mm (3.23") to 93 mm (3.66") (typical) |
|
Workstand W x D x H: |
105 x 175 x 90 mm (4.1" x 6.9" x 3.5") |
SHIPPING
A delivery and handling charge applies to all orders with the exception of back-ordered items.
Unless otherwise required by Buyer, Seller will make transport arrangements as follows:
For deliveries within the metropolitan areas of mainland State capital cities a standard freight charge may be added to invoice; goods
For delivery outside those areas, seller will select the transport to be used and prepay freight for Buyer. Seller will then bill Buyer for freight at Seller's discretion.
Should the Buyer request goods be sent to a Post Office box the Buyer acknowledges this method is the only available and therefore the Seller is not liable for undelivered goods.
Free shipping on orders over $199 incl GST (valid for 1 delivery per order and excludes NT, WA & TAS). If only part of the order is in stock, the customer has the option of paying for a second delivery if they require a partial shipment prior to all goods becoming available. Mektronics Australia reserves the right to charge additional freight in the event of hazardous, bulky or heavy items ordered.
DELIVERY TIME
All quoted delivery or consignment dates are estimates only, given without engagement.
Delay in consignment of any part of an order shall not relieve Buyer of its obligation to accept and pay for the remainder of the order.
Except as provided in paragraph 1.2 of Terms & Conditions, seller will not be liable to pay damages or compensation for any injury or loss sustained by Buyer
a) in the event of a delay in consignment or delivery of goods: or
b) in the event of non delivery.
Goods offered ex-stock by Seller are subject to prior sale.
In the event of any happening beyond Seller's reasonable control in consequence of which Seller cannot effect consignment by the time or times quoted or specified, Seller shall be entitled to consign part only of an order, suspend consignment or extend the time for consignment, for the period during which such cause of delay operates, or may cancel the order, and in the event of such suspension, extension or cancellation, Seller shall not be liable for damages.
